Channel section/master section

Channel section

1.​Channel level indicator

Displays the volume level before the sound passes through the channel fader.

2.​TRIM knob

Adjusts the volume for the channel input sound.

3.​EQ/ISO (HI, MID, LOW) knobs

Adjusts the volume of each frequency band.
Each knob adjusts in the following range.

—​[HI]: -∞ dB to +6 dB (ISO)/-26 dB to 6 dB (EQ)

—​[MID]: -∞ dB to +6 dB (ISO)/-26 dB to 6 dB (EQ)

—​[LOW]: -∞ dB to +6 dB (ISO)/-26 dB to 6 dB (EQ)

4.​COLOR knob

⇨Using Sound Color FX

5.​Channel fader

Adjusts the volume for the channel output sound according to the channel fader curve set with [Channel Fader Curve] on the [MIXER SETTINGS] screen or in the Utility settings. Moving it up increases the volume, and down decreases the volume.

⇨Channel Fader Curve

⇨Channel Fader Curve

6.​Crossfader

Adjusts the volume balance between the channel output sounds according to the crossfader curve specified with [Crossfader Curve] on the [MIXER SETTINGS] screen or in the Utility settings.

⇨Crossfader Curve

⇨Crossfader Curve

Master section

7.​MASTER level knob

Adjusts the volume for the master sound.

Outputting sound

■Adjusting the channel input volume

1​Turn the [TRIM] knob to adjust the volume for the input sound.

The channel level indicator lights up when sound is input to the channel.

■Adjusting the channel output volume

1​Move the channel fader to adjust the volume for the output sound.

2​Move the crossfader to adjust the volume balance of the 2 channels.

■Adjusting the master sound volume

1​Turn the [MASTER LEVEL] knob to adjust the volume for the master sound.

The master level indicator lights up when the master sound is output.

Adjusting the sound

1​Turn the [EQ/ISO (HI, MID, LOW)] knobs to adjust the volume of each band.

•​Set the function (equalizer or isolator) to adjust with the [EQ/ISO (HI, MID, LOW)] knobs in [EQ/ISO] on the [MIXER SETTINGS] screen or in the Utility settings.

⇨EQ/ISO

⇨EQ/ISO

Setting the faders

Set the channel fader and crossfader.

■Setting the channel fader

1​Press the [MIXER SETTINGS] button.

The [MIXER SETTINGS] screen appears.

2​Set the channel fader curve in [Channel Fader Curve].

—​: Steeply raises the volume when the channel fader is moved close to the top position.

—​: Gradually raises the volume as the channel fader is moved up.

—​: Steeply raises the volume as the channel fader is moved from the bottom position.

•​You can also set it in [Channel Fader Curve] on the [MIXER SETTINGS] screen or in the Utility settings.

⇨Channel Fader Curve

⇨Channel Fader Curve

■Setting the crossfader

1​Press the [MIXER SETTINGS] button.

The [MIXER SETTINGS] screen appears.

2​Set the crossfader curve in [Crossfader Curve].

–​THRU: Outputs sounds from Deck 1 and Deck 2 regardless of the crossfader position.

–​: Gradually raises the volume of the sound assigned to the other side as the crossfader is moved from one side (Deck 1 or Deck 2 side) to the other, and decreases the volume of the sound on the side it is moving away from.

–​: Steeply raises the volume of the sound assigned to the other side as the crossfader is moved from one side (Deck 1 or Deck 2 side) to the other.

•​You can also set it in [Crossfader Curve] on the [MIXER SETTINGS] screen or in the Utility settings.

⇨Crossfader Curve

⇨Crossfader Curve