Settings

Changing the settings from the Deck Settings screen

1Press the [DECK SETTINGS] button.

The [DECK SETTINGS] screen appears.

•Change common deck settings at the top of the screen and each deck settings at the bottom of the screen.

2Touch a setting value.

• Touch i_close on the title/status bar to close the [DECK SETTINGS] screen.

Setting item		Description
Common deck settings
	Smart Cue	Determines whether or not a cue point is automatically set when a Hot Cue/Loop is set or playback starts from a Hot Cue/Loop. ⇨Setting a Hot Cue ⇨Setting a loop ⇨Starting playback from a Hot Cue •Setting values: OFF*, ON
	Gate Cue	Determines whether or not gate playback is enabled when operating hot cues/loops. ⇨Starting gate playback from a Hot Cue •Setting values: OFF*, ON
	Auto Cue (Memory Cue)	Turns on and off Auto Cue. ⇨Setting Auto Cue •Setting values: OFF, ON*
	Waveform Current Position	Sets where to display the current playback point (center or left) on the enlarged waveform. •Setting values: LEFT*, CENTER
	QUANTIZE Beat Value	Sets the number of beats for Quantize. •Setting values: 1/8, 1/4, 1/2, 1*
	Vinyl Speed Adjust (Release)	Sets the playback and stop speeds in Vinyl mode. ⇨Adjusting the playback starting and stopping speeds (for Vinyl mode) •Setting values: OFF*, ON
	Waveform Color	Changes the waveform color. •Setting values: BLUE, RGB, 3BAND
	LCD Brightness	Sets the brightness of the main display. •Setting values: 1, 2, 3*, 4, 5
Each deck settings
	VINYL	Turns on and off Vinyl mode. ⇨Setting the jog wheel mode
	QUANTIZE	Turns on and off Quantize (for deck). ⇨Using Quantize
	SLIP	Turns on and off Slip mode. ⇨Slip mode
	MEMORY CUE	Saves cue/loop points. ⇨Saving a cue point ⇨Saving a loop
	TEMPO	Changes the variable range of the TEMPO slider. ⇨Adjusting the playback speed (tempo control)
	MASTER TEMPO	Turns on and off Master Tempo. ⇨Adjusting the playback speed without changing the pitch (Master Tempo)

*: Factory setting

Changing the settings from the Mixer Settings screen

1Press the [MIXER SETTINGS] button.

The [MIXER SETTINGS] screen appears.

2Touch a setting value.

⇨Mixer Settings

• Touch i_close on the title/status bar to close the [MIXER SETTINGS] screen.

■Mixer Settings

Setting item		Description
MIC settings
	MIC EQ (+-12dB) HIGH	Adjusts the volume of sound (-12 dB to +12 dB (10 kHz)) input from the [MIC] terminal.
	MIC EQ (+-12dB) LOW	Adjusts the volume of sound (-12 dB to +12 dB (100 Hz)) input from the [MIC] terminal.
	Talk Over	Turns on and off talkover. ⇨Using a microphone •Setting values: OFF*, ON
Mixer settings
	EQ/ISO	Sets the function (equalizer or isolator) to adjust with the [EQ/ISO (HI, MID, LOW)] knobs. •Setting values: EQ*, ISO
	Channel Fader Curve	Sets the channel fader curve. ⇨Setting the channel fader •Setting values: Curve1, Curve2*, Curve3
	Crossfader Curve	Sets the crossfader curve. ⇨Setting the crossfader •Setting values: THRU, Curve2, Curve3*
Headphones settings
	Headphones	Sets the output method ([MONO SPLIT] or [STEREO]) for the headphones monitor sound. •Setting values: MONO SPLIT, STEREO*
	Touch Preview Volume	Adjusts the volume balance of the Touch Preview sound. ⇨Monitoring with headphones
	SonicLink	Turns on and off SonicLink. ⇨Monitoring with SonicLink headphones •Setting values: OFF, ON*
	Bluetooth Input	Sets whether to input sound from a mobile device, etc. ⇨Pairing with a mobile device (Bluetooth input) •Setting values: OFF*, ON •Either of [Bluetooth Input] or [Bluetooth Output] can be set to [ON].
	Bluetooth Output	Sets the settings for sound output from mobile speakers, etc. ⇨Connecting to a mobile speaker, etc. (Bluetooth output) •Setting values: OFF*, ON •Either of [Bluetooth Input] or [Bluetooth Output] can be set to [ON].
	USB REC	Records the same audio as the output from the [MASTER 1] and [MASTER 2] terminals into a WAV file on a USB storage device. ⇨Recording

*: Factory setting

Changing the settings from the Utility settings

1Touch i_launcher (Menu) on the title/status bar.

The menu is displayed.

2Touch [UTILITY].

The [UTILITY] screen appears.

1.Category

2.Setting items and current setting values

3.Setting values

3Select a category.

4Select a setting item.

⇨Utility settings

5Select a setting value.

• Touch i_close on the title/status bar to close the [UTILITY] screen.

■Utility settings

Deck

Setting item		Description
Load Lock		Determines whether or not you can load another track during playback. •Setting values: Unlock^*, Lock
Gate Cue		Determines whether or not gate playback is enabled when operating hot cues/loops. ⇨Starting gate playback from a Hot Cue •Setting values: OFF*, ON
Smart Cue		Determines whether or not a cue point is automatically set when a Hot Cue/Loop is set or playback starts from a Hot Cue/Loop. ⇨Setting a Hot Cue ⇨Setting a loop ⇨Starting playback from a Hot Cue •Setting values: OFF*, ON
Auto Cue Level		Sets the sound pressure level that Auto Cue recognizes as silence. •Setting values: -78dB, -72dB, -66dB, -60dB, -54dB, -48dB, -42dB, -36dB, Memory Cue*, Hot Cue •[Memory Cue]: Sets the saved cue/loop point closest to the beginning of a track to an Auto Cue point. •[Hot Cue]: Sets the saved Hot Cue/Loop point closest to the beginning of a track to an Auto Cue point. [] turns [ AUTO] on the waveform screen when Auto Cue is turned on.
Vinyl Speed Adjust		Sets the playback and stop speeds in Vinyl mode. ⇨Adjusting the playback starting and stopping speeds (for Vinyl mode) •Setting values: Touch & Release, Touch*, Release,
Play Mode		Sets playback mode. •Setting values: Continue, Single* •[Continue]: Automatically loads the next track when playback reaches the end of a track. •[Single]: Stops playback when playback reaches the end of a track. The next track isn’t automatically loaded.
Waveform Current Position		Sets where to display the current playback point (center or left) on the waveform. •Setting values: LEFT*, CENTER

*: Factory setting

Mixer

Setting item		Description
Master Attenuator		Sets the attenuation level of the sound output from the [MASTER 1] or [MASTER 2] terminals. •Setting values: -12dB, -6dB, 0dB*
Master Mono/Stereo		Sets the output method ([Stereo] or [Mono]) for the sound output from the [MASTER 1] and [MASTER 2] terminals. •Setting values: Stereo*, Mono
EQ/ISO		Sets the function (equalizer or isolator) to adjust with the [EQ/ISO (HI, MID, LOW)] knobs. •Setting values: EQ*, ISO
Channel Fader Curve		Sets the channel fader curve. ⇨Setting the channel fader •Setting values: Curve1, Curve2*, Curve3
Crossfader Curve		Sets the crossfader curve. ⇨Setting the crossfader •Setting values: THRU, Curve2, Curve3*
SonicLink		Turns on and off SonicLink. ⇨Monitoring with SonicLink headphones •Setting values: OFF, ON*
Headphones Mono Split/Stereo		Sets the output method ([Mono Split] or [Stereo]) for the headphones monitor sound. •Setting values: Mono Split, Stereo*
Mic Output to Master REC		Determines whether or not to output the microphone sound to Master Rec (recording sound). •Setting values: Off, On*
Mic Output to USB Output		Determines whether or not to output the microphone sound to the USB port (Type-C). •Setting values: Off, On*
Mixer Mode		Sets the audio output when a PC is connected to the unit. •Setting values: XDJ-AN, MIDI Control*

*: Factory setting

Network

Setting item	Description
Wi-Fi Setting	Sets wireless LAN (Wi-Fi). ⇨Wireless LAN (Wi-Fi®) connection
Wi-Fi Frequency	Sets the wireless LAN (Wi-Fi) frequency band. •Setting values: 5GHz (Recommended)*, 2.4GHz/5GHz •We recommend 5 GHz band, which has stable communication. •Before changing the setting, turn off wireless LAN (Wi-Fi). ⇨Wireless LAN (Wi-Fi®) connection
Wi-Fi Address	Displays MAC address for the wireless LAN (Wi-Fi) connection.

Setting item

Description

Wi-Fi Setting

Sets wireless LAN (Wi-Fi).

⇨Wireless LAN (Wi-Fi®) connection

Wi-Fi Frequency

Sets the wireless LAN (Wi-Fi) frequency band.

•Setting values: 5GHz (Recommended)*, 2.4GHz/5GHz

•We recommend 5 GHz band, which has stable communication.

•Before changing the setting, turn off wireless LAN (Wi-Fi).

⇨Wireless LAN (Wi-Fi®) connection

Wi-Fi Address

Displays MAC address for the wireless LAN (Wi-Fi) connection.

*: Factory setting

Bluetooth

Setting item	Description
Bluetooth Input	Sets whether to input sound from a mobile device, etc. ⇨Pairing with a mobile device (Bluetooth input) •Setting values: Off*, CH1, CH2 •Either of [Bluetooth Input] or [Bluetooth Output] can be turned on.
Bluetooth Output	Sets the settings for sound output from mobile speakers, etc. ⇨Connecting to a mobile speaker, etc. (Bluetooth output) •Setting values: Off*, On •Either of [Bluetooth Input] or [Bluetooth Output] can be turned on.

Setting item

Description

Bluetooth Input

Sets whether to input sound from a mobile device, etc.

⇨Pairing with a mobile device (Bluetooth input)

•Setting values: Off*, CH1, CH2

•Either of [Bluetooth Input] or [Bluetooth Output] can be turned on.

Bluetooth Output

Sets the settings for sound output from mobile speakers, etc.

⇨Connecting to a mobile speaker, etc. (Bluetooth output)

•Setting values: Off*, On

•Either of [Bluetooth Input] or [Bluetooth Output] can be turned on.

*: Factory setting

General

Setting item		Description
Language		Sets the display language.
LCD Brightness		Sets the brightness of the main display. •Setting values: 1, 2, 3*, 4, 5
Screen Saver		Sets the screen saver. •Setting values: Off, On* •When set to [On], the screen saver starts if: –You don’t use the unit for more than 5 minutes when a track isn’t loaded. –You don’t use the unit for more than 100 minutes during pause, during cue standby, or after playback reaches the end of a track. •Use the unit to cancel the screen saver.
Power Management		Sets the Power Management function ⇨Power Management •Setting values: Never, 20min*
Demo Mode		Lights up LED of all buttons. •Setting values: Off*, On
Restore Defaults		Restores the settings to the factory settings. •Setting values: Cancel*, Ok

*: Factory setting

Info

Setting item		Description
Version No.		Displays the software version of the unit.
Serial No.		Displays the serial number of the unit.
License		Displays the license information of the unit.

■Power Management

When [Power Management] is set to [20min], the unit automatically turns off after 20 minutes of inactivity if no audio signal is input to the unit.

•The factory setting is [20min].

•Set [Power Management] to [Never] if you don’t need to use the Power Management function.

•Power consumption may increase when [Power Management] is set to [Never].

Calling up My Settings saved on a USB storage device

You can call up My Settings from a USB storage device.

•You can call up My Settings from rekordbox connected in the PRO DJ LINK network or rekordbox CloudDirectPlay.

1Connect a USB storage device to the unit.

⇨Storage device connection (USB)

2Touch [SOURCE] on the title/status bar.

The [SOURCE] screen appears.

3Select a source.

4Touch [MY SETTINGS LOAD] in the source information.

My Settings are called up.

•You can’t call up My Settings when a track is playing. Pause the playback before calling up the settings.